Gateway Wireless Office Headset AG 168V User Manual

AG-168V SIP GATEWAY User Manual (V1.42)

AG-168V SIP GATEWAY User Manual

ꢀ

AG-168V SIP GATEWAY Appearance Introduction:...................................................... 2

Features ................................................................................................................................ 2

Function Keys of AG-168V SIP GATEWAY Introduction........................................... 3

Standard and Protocol......................................................................................................... 4

Operating requirements ...................................................................................................... 5

Electric requirements........................................................................................................... 5

Size ........................................................................................................................................ 5

Installation ............................................................................................................................. 6

Configuration......................................................................................................................... 6

GATEWAY Keypad set........................................................................................................ 6

Configured by WEB ............................................................................................................. 7

Configured by PalmTool.................................................................................................... 23

Telnet Configuration........................................................................................................... 23

Use AG-168V Gateway..................................................................................................... 41

Upgrade AG-168V SIP GATEWAY................................................................................ 43

AG-168V SIP GATEWAY User Manual (V1.42)

ꢀ Indicator light and function

Indicator

light

Function

Indicator

light

Function

Power

Tel

Status

Power on ,indicating power

communicaing flash,

Registered off, not registered flash

Buttons

Function

voice indicating “local ip ” , refer to “GATEWAY Keypad set” chaptor

set different way of internet connection, refer to “GATEWAY Keypad set” chaptor

Set static ip address when in “static mode ”

enable AG-168V into “setting mode ”, refer to “GATEWAY Keypad set” chaptor

ꢀ

Hardware

Main chip—pa1688PQ 50MHz

Data Memory—1MB SDRAM

Program Memory—2MB Flash memory

Ethernet Jack—1 10M jacks

FXS Port-1 FXS Port for Tel

Line Port -1 Line port for PSTN

AC/DC adapter—Output 12V DC, 450mA

ꢀ Software

DHCP support for LAN or Cable modem

PPPoE support for ADSL or Cable modem

Set GATEWAY by HTTP web browser (IE6.0) or Telnet

Upgrade by FTP

Support major G.7XX and gsm610 audio codec

AG-168V SIP GATEWAY User Manual (V1.42)

Dynamic voice jitter buffer

G.168/165 compliant 16ms echo cancellation

Tone generation and Local DTMF re-generation according with ITU-T

E.164 dial plan and customized dial rules

100 entries for quick dial

Voice prompt

Hotline

ꢀ Standard and Protocol

Gateway supports following standard and protocol:

IEEE 802.3 /802.3 u 10 Base T / 100Base TX

Major G.7XX and gsm610 audio codec

SIP RFC3261

TCP/IP: Internet transfer and control protocol

RTP: Real-time Transport Protocol

RTCPꢀReal-time Control Protocol

VAD/CNG save bandwidth

DHCPꢀDynamic Host Configuration Protocol

PPPoEꢀPoint to Point Protocol over Ethernet

DNSꢀDomain Name Server

TelnetꢀInternet's remote login protocol

FTPꢀFile Transfer protocol

HTTPꢀHyper Text Transfer protocol

ꢀ Operating requirements:

Operation temperature: 0 to 50°C (32°to 122°F)

Storage temperature: -30°to 65°C (-22°to 149°F)

Humidity: 10 to 90% no dew

ꢀ Electric requirements:

Voltage: 9V~12V DC

Power adapter: DC 12V/450mA

AG-168V SIP GATEWAY User Manual (V1.42)

Network interface:1 RJ-45 Ethernet Connectors

FXS:1 RJ-11 For Tel

Line:1 RJ-11 For PSTN

ꢀ Size

150 x 110 x 28 mm (L x W x H)

ꢀ Installation:

Connecting to network: connecting one side of the cable to the lan port of AG-168V,

the other side to PBX or HUB or ADSL and Cable Modem’s lan port..

Connecting to phone: Insert one side of RJ11 line to the Tel port of AG-168V ,

the other side to the phones’ interface. Connecting the Line’s port of

AG-168V to PSTN line. Power on with the adaptor from the packaging.

AG-168V SIP GATEWAY User Manual (V1.42)

ꢀ Configuration

Two different ways can be used to configure AG-168V H323 phone:

phone web browser, Telnet commands on computer.

ꢀ Phone Keypad setup

Using the keyboard of the normal phone connecting to AG-168V FXS

port and the “IP key” , which can preset and enter into “Setting mode” ,

operation as below:

Operation

Function

with handset of FXS port ‘s phone hung, press IP ,voice promt “local ip”

with handset of FXS port ‘s phone hung, press default password, then

input the number of X + “ IP” button in order to set different network

connection

1234+X+ IP

X valued 0 = stataic IP; 1 = DHCP ; 2 = PPPoE; 3= modem

3 with handset of FXS port ‘s phone hung, press default password, and

press “ IP” button, enter “setting mode”

1234+ IP

4 with handset of FXS port ‘s phone hung, press default password, then

1234+xxx.xxx.xxx.xx

AG-168V SIP GATEWAY User Manual (V1.42)

input the ip address xxx.xxxx.xxx.xxx, press “ip ” button . Using the button

of * for —,

+ IP

ꢀ Configured by WEB

Double click

icon to open the IE browser. Input the IP address of the GATEWAY

into address bar (

), and then input password of the

GATEWAY into the following page. Default password 1234 is ordinary password and

super password is 12345678. With Debug set 0[disable], please input super password;

while Debug is not set as 0[disable], please input ordinary password. Then

click

button. The following configured page wills popup. Refer to Fig 3.1

please.

AG-168V SIP GATEWAY User Manual (V1.42)

Fig 3.1 Http Setting

Network Setting

Fig 3.2 Network Setting

iptype: Set how IP GATEWAY gets relevant network parameters by selecting

corresponding item from drop down list.

ꢁ

static ip: Select this item to authorize users set IP address, subnet mask and

router IP address of IP GATEWAY manually.

ꢁ

dhcp: Select this item to enable DHCP mode. With this system, your LAN or router

automatically assigns all the required network parameters to any device connected

to it when the device log on. AG-168V IP GATEWAY is shipped from the factory

with DHCP on. So, if you’re LAN or router is configured to use DHCP addressing,

the IP GATEWAY’s LAN parameters will automatically be configured as soon as it is

connected to the LAN or router and powered up.Default IP address of the AG-168V

is192.169.1.100.

ꢁ

pppoeꢀThose ADSL and Cable Modem users please select this item for it is a

protocol especially designed for them. With this system, ADSL ISP automatically

assigns all the required IP parameters to any device connected to it when the

device log on

ꢁ

modemꢀIf the IP GATEWAY used with modem, please select this item to get

AG-168V SIP GATEWAY User Manual (V1.42)

relevant network parameters auto. Then please fill ID and pin into ppp id and

ppppin fields

ppp id: With pppoe or modem selected in iptype drop down list, please enter the

user name here.

ppp pin: With pppoe or modem selected in iptype drop down list, please enter the

password here.

local ip: With static ip selected in iptype drop down list, please enter IP address of

IP GATEWAY here

subnet mask: With static ip selected in iptype drop down list, please enter

subnet mask of IP GATEWAY here

router ip: With static ip selected in iptype drop down list, please enter router IP

address of IP GATEWAY here

dns: With static ip selected in iptype drop down list, please enter IP address of

DNS server here

dns 2: With static ip selected in iptype drop down list, please enter IP address of

backup DNS server here

mac: MAC address is the physical address supplied by the Ethernet NIC.

AG-168V GATEWAY is shipped from the factory with a unique algorism MAC

address printed on the back of the base

AG-168V SIP GATEWAY User Manual (V1.42)

Protocol Setting

Fig 3.3 Protocol Setting

use service: Enable/disable service by checking/clearing this box.

To make calls through gatekeeper, please check this box; otherwise, GATEWAY can

only make IP-to IP calls or calls through gateway

server every “register ttl” seconds. The minimum value is 10, maximum value is

65535. Default is 60.

service type: This option is used to accommodate the miscellaneous

requirements of the system providers. When IP GATEWAY is connected to these

systems, please select the corresponding service type.

ꢂ

commonꢀno special requirementsꢀ

huawei: use huawei’s systemꢀ

zte: use zte’s systemꢀ

harbour: use harbour’s systemꢀ

utstarcom: use utstarcom’s systemꢀ

uptech: use uptech’s systemꢀ

AG-168V SIP GATEWAY User Manual (V1.42)

ꢂ

kaimenꢀuse kaimen’s systemꢀ

mediaring: use mediaring’s systemꢀ

italkbb: use italkbb’s systemꢀ

stanaphone: use stanaphone’s systemꢀ

net2phone: use net2phone’s systemꢀ

fwd: use fwd(freeworlddialup) systemꢀ

ipphonex: use ipphonex’s systemꢀ

sipphone: use siphone’s systemꢀ

ngtel: use ngtel’s systemꢀ

ayctel: use AycTe’s systemꢀ

SIP proxy: when user service write SIP Proxy Server URI.

Domain/realm : set SIP serve address domain

nat traversal: When the IP GATEWAY with private IP address need communicate

with other IP GATEWAYs in a different LAN or on Internet, please select an item from

dropdown list to set the proxy used by the GATEWAY.

ꢁ

disable: Select this item when the log in server and IP GATEWAY in the same

LAN, or the log in system supports the IP GATEWAY working behind the LAN.

ꢁ

enable: When the system does not support IP GATEWAY working behind the

LAN, please select this item to search public IP address of the NAT device. With

this item selected, “nat addr” field will be activated. Besides, port mapping (port

forwarding) needs to be properly set up on NAT device.

ꢁ

Stun: When Stun used for appendix for cross NAT , choose STUN. nat add will

be activated.

nat addr: When “nat traversal” is set to “enable”, please put the domain name of

the servers ( These web server helps to find out the public IP of the IP GATEWAY)

into “nat addr”, such as www.whatismyip.com.

nat ttl: When IP GATEWAY sit behind a NAT device, it will send packets to server

AG-168V SIP GATEWAY User Manual (V1.42)

every “nat ttl” seconds to keep the port mapping on the NAT device alive. “nat ttl” is

an integer between 10 and 65535 .default value is 20.

phone number: set local ID

account: set aaa@bbb format account register

pin: set password

handshaking messages. Default is 5060

rtp port : RTP port is the port transferring and receiving voice packets using UDP

protocol. This is an even number between 1024 and 65535, can’t be the same as

“register port”.

rtp tos: Set the TOS field of the IP header of the RTP packets. The bigger this

value is 0, the higher priority the packet is.

local type: This parameter refers to how IP GATEWAY authenticate itself to the

gatekeeper. The meaning of each item is as follow:

ꢁ

auto: use support automated negotiate authentication account and pin about MD5

or CAT .

ꢁ

md5: use MD5 authentication account and pin.

cat: use CAT authentication account and pin.

sha1: use SHA1 authentication account and pin.

call type: Set call type by selecting the items in drop down list.

ꢁ

normal: Call out in normal way by selecting this item.

advanced: Call out in faststart and tunneling way by selecting this item. It is a

AG-168V SIP GATEWAY User Manual (V1.42)

recommended way with SIP protocol used

dtmf: Set DTMF signal sending way by selecting control string, inband audio,

signal keypad or rfc 2833 ,sip infofrom list box

dtmf payload: set use RTP send DTMF’s RTPꢀthe value range is 96-101ꢀ

gatekeeper every “register ttl” seconds. The value range is 10-65535. Default is 60.

Super password : Set super password. Default is 12345678

debug: Set the debug level of the GATEWAY.

ꢁ

disable: Disable output the debug message by selecting this item.

output: Output the operation information to the window, such as register, input

by selecting this item.

ꢁ

output all: Output all debug information and data in test window by selecting this

item.

remote debug: Save the debug information in SDRAM of IP GATEWAY by

selecting this item.

no check: Disable checking firmware tags when upgrading. This is not

suggested, because it will increase the risk of upgrading the wrong firmware into

the GATEWAY.

phone settings:

AG-168V SIP GATEWAY User Manual (V1.42)

Fig 3.4 phone Setting

use dialplan: Set whether use dial plan or use dial number by selecting the

corresponding item in drop down list.

ꢁ

disable: Do not use dial plan or dial number by selecting this item.

enable: Use dial plan by selecting this item.

dialnum: Use dial number by selecting this item. With this item selected, please

enter the dial prefix into dial number field.

ꢁ

prefix: Use 179XX service by selecting this item.

Hotline: Use Hotline function by selecting this item. With this item selected, please enter

the hotline number into dial number field.

dial number: With dialnum selected in use dialplan drop down list, please

enter the dial prefix into this field according to requirement of log in server. For

example, with eTalk card used, enter 00 here.

ddd code: With enable or dialnum selected in use dialplan drop down list, set

area code according to E.164 dial rule. For example, Beiing 10; Shanghai 21.

idd code: With enable or dialnum selected in use dialplan drop down list, set

country code according to E.164 dial rule. For example, China 86; U.S.A .1.

idd prefix: With enable or dialnum selected in use dialplan drop down list, set

international call prefix according to E.164 dial rule, such as 00.

AG-168V SIP GATEWAY User Manual (V1.42)

ddd prefix: With enable or dialnum selected in use dialplan drop down list, set

long distance call prefix according to E.164 dial rule, such as 0.

inner line: Enable/disable innerline call by selecting corresponding items from

dropdown list.

ꢁ

disable: Disable call innerline by selecting this item.

enable: enable call innerline by selecting this item.

omit prefix Enable , ingnore the number of the inner line prefix , cooperated

with special system

inner line prefix: default is 0

nonlocal prefix: With enable selected in innerline dropdown list, please fill the

number switching to long-distance call, such as 9

Call waiting: Enable/disable call waiting by checking/unchecking the box.

Use digitmap: Enable/disable digit map by checking/unchecking the box.

forward number: Enter receiving forwarded calls GATEWAY number into this

field; If the IP GATEWAY used with modem, with modem item selected in iptype list

box, and then fill ISP number into this field.

fwd poweroff: Forward calls if power off by checking this box. Please enter

receiving forwarded calls GATEWAY number into fwd number field.

fwd noanswer: Forward calls without replying by checking this box. Please enter

receiving forwarded calls GATEWAY number into fwd number field.

fwd always: Forward all calls by checking this box. Please enter receiving

AG-168V SIP GATEWAY User Manual (V1.42)

forwarded calls GATEWAY number into fwd number field

fwd busy: Forward calls if busy by checking this box. Please enter receiving

forwarded calls GATEWAY number into fwd number field.

answer: Enter a number from 0 through 60 to set the entries of the seconds before

the GATEWAY answer the call auto or forward the calls.

handset in: Drag the slider to adjust the volume of handset input. Drag it to the left

to reduce the volume; while drag it to the right to increase the volume

handset out: Drag the slider to adjust the volume of handset output. Drag it to the

left to reduce the volume; while drag it to the right to increase the volume

Dual mode set AG-168V FXS PSTN portꢀ

ꢁ

disable AG-168V FXS Not user PSTNꢀ

PSTN first set AG-168V FXS first user PSTN callꢀ

IP first set AG-168V FXS first user ip callꢀ

dual mode prefix set dual mode prefix IP firstꢀset PSTN prefix

Audio settings:

Fig 3.5 Audio Setting

vad: Enable/disable VAD (voice activity detection)

agc: Enable/disable AGC.

aec: Enable/disable VEC

codec1: Set the priority 1of the audio compression algorithm. The options are

g729ꢀg7231ꢀg711uꢀg711a and gsm.

codec2: Set the priority 2of the audio compression algorithm. The options are

AG-168V SIP GATEWAY User Manual (V1.42)

g729ꢀg7231ꢀg711uꢀg711a and gsm.

codec3: Set the priority 3of the audio compression algorithm. The options are

g729ꢀg7231ꢀg711uꢀg711a and gsm

codec4: Set the priority 4of the audio compression algorithm. The options are

g729ꢀg7231ꢀg711uꢀg711a and gsm.

codec5: Set the priority 5of the audio compression algorithm. The options are

g729ꢀg7231ꢀg711uꢀg711a and gsm.

g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is 6.3kbps,

low rate is 5.3kbps.

Other settings:

Fig 3.6 Other Setting

password: Set the password of the GATEWAY. (Default password is 1234).

Upgrade type: user FTP upgrade

ꢁ

disable: Disable output the debug message by selecting this item.

all: check hard type upgrade.

mac: check mac address auto upgrade.

Ppp id: check pppid auto upgrade.

account: check account auto upgrade.

AG-168V SIP GATEWAY User Manual (V1.42)

ꢁ

Phonenumber: check phonenumber auto upgrade.

upgrade addr: Put IP address or domain name obtained by ISP of FTP server

supplying upgrade program into this field.

nts ip: Fill IP address of time server here.

use daylight: Enable/disable daylight

timezone: Select correct time zone in list box

When debug set as 0[disable], if input ordinary password (default one is 1234), then following page

will pop up after clicking . And only those parameters can be modified.

Fig 3.7 Setting Page using ordinary pin with Debug set as 0 [disable]

Update: Click this button to save the configuration and the GATEWAY will reboot.

Once the GATEWAY reboots successfully, the new configuration is effective.

Note After entering set page, if Update button is not clicked within 5 seconds, then

when you click it again, the index page asking for pin will pop up again. Then

please input the password again to enter the set page and then click Update

AG-168V SIP GATEWAY User Manual (V1.42)

button to confirm the modification.

Click this button to open the speed dial settings page. Please refer to Fig

phone Book:

3.7. In this page, you can set and save the speed dial number by typing the name into the

Name field and then entering the corresponding number following the name. For example,

input Jack in Name field following 001, and then input 5989426454 into GATEWAY

number field. Then Jack’s number 5989426454 is saved in GATEWAY book. Then please

click Save/Back button. In normal state, you can use speed dial to call numbers saved in

GATEWAY book.

Fig 3.8 GATEWAY Book Illustration

Upgrade Program: Click this button to update the program of IP GATEWAY. Before

updating, please fill IP address of FTP server into upgrade addr field, and then click this

button. Then the GATEWAY will read the corresponding bin files from the server and then

load into the GATEWAY

Update Digitmap: Click this button to update the digitmap of the GATEWAY. Before

updating, please fill IP address of FTP server into upgrade addr field, and then click this

button. Then the GATEWAY will read the corresponding map files from the server and then

load into the GATEWAY.

Note Please refer to PalmTool User Guide to learn how to write digitmap or just

download TXT file from our site. Then please save it as “GATEWAY type.map”

file, such as AT168S.map.

ꢀ Configured by PalmTool

PalmTool is a tool designed especially to configure and upgrade the PA168 IP GATEWAY. On a PC

AG-168V SIP GATEWAY User Manual (V1.42)

connecting with the GATEWAY or at the same segment of the GATEWAY, double click

open the PalmTool. The index page of PalmTool will popup.

icon to

a) Input the IP address of the GATEWAY into Local IP field (such as 192.168.1.100), and

then click “GATEWAY Settings” button.

From Version1.24, use PalmTool to set the IP GATEWAY, please set debug as output or

output all firstly, or PalmTool cannot connect IP GATEWAY. The parameters of PalmTool is

same as the parameters in HTTP, so please refer to HTTP set chapter to learn how to set

IP GATEWAY

ꢀ Telnet Configuration

On the PC choose Start>Run, and then type telnet 192.168.1.100 into Run field

in popuping Run dialog. Or input telnet 192.168.1.100 in the DOS window. Then

the following information will be displayed

AG-168V V1.39 settings

Password :

Then please type password. With debug is set as 0[disable], if type ordinary password

(default one is 1234), after Retun, you will seeꢀ

Password : ****

P:\>

If you type super password, then you will see:

Password : ********

P:\>

Above information indicates that IP GATEWAY is under setting mode, and then you can set

the AG-168V IP GATEWAY by using the telnet commands.

ꢀ

AG-168V Telnet Commands Explanation

AG-168V Telnet Commands

Comman

Function

Supply command name and parameters

AG-168V SIP GATEWAY User Manual (V1.42)

get

set

Display basic parameters of the AG-168V IP GATEWAY

Set parameters of the AG-168V IP GATEWAY

Save current settings to designated position

store

load

exit

Load designated settings to current position

Exit from the setting mode without saving the configuration

Exit with saving all configurations and restart AG-168V

Ping other net parameter

write

ping

ftp

The GATEWAY connects to FTP server and then get the files

Detail description of AG-168V Telnet commands

Command

Syntax description: No optional parameter

Usage: Type command name and parameters following P:\> . Be used as the

keyword to supply keyword and parameters of the relevant commands.

Relevant usage: None

Detailed description:

List help of all commands

For example:

P:\>?

set

get

list settings

store x

load x

exit

store current to xth settings

load xth settings to current

write

save settings

Command get

AG-168V SIP GATEWAY User Manual (V1.42)

Syntax description: No optional parameter of keywords

Usage: Display basic parameters of the AG-168V IP GATEWAY

Relevant usage: None

Detailed description:

get

Display basic running parameters of the AG-168V IP GATEWAY.

Input ordinary password without debug being set as 0[disable], or input super

password with debug set as 0[disable], then following parameters of IP GATEWAY

will be displayed:

AG-168V V1.39 settings

Password: ********

P:\>get

iptype 0[static]

ip 192.168.1.100

subnetmask 255.255.255.0 router 192.168.1.254

dns 202.106.196.152

service 1[enable]

dns2 202.106.196.115

mac 00-09-45-65-a3-e6

servicetype 0[common] serviceaddr 203.93.9.57

serviceid [empty]

nattraversal 1[enable]

nataddr www.showmyip.com natttl 30

GATEWAYnumber 182378009 account [empty]

pin [empty]

controlport 6802

rtpport 6802

registerport 6800

registerttl 60

signalport 6800

rtptos 0

jitter size 0

calltype 1[advanced]

string]

localtype 0[GATEWAYnumber]

dtmf 0[control

dtmfpayload 101

dialplan 2[dialnum]

iddcode [empty]

innerline 1[enable]

answer 5

dialnumber 17911

iddprefix [empty]

localprefix 0

dddcode [empty]

dddprefix [empty]

nonlocalprefix 0

ringtype 0[dtmf0]

fwdpoweroff 1[enable]

fwdbusy 0[disable]

audioframes 1

digitmap 0[disable]

fwdnumber [empty]

fwdalways 0[disable]

audiotype 0[g7231]

vad 1[enable]

fwdnoanswer 0[disable]

6.3k 1[enable]

agc 0[disable]

aec 1[enable]

handsetin 9

handsetout 21

speakerout 21

codec1 1[g7231]

codec4 4[gsm]

codec2 0[g729]

codec5 5[null]

codec3 2[g711u]

AG-168V SIP GATEWAY User Manual (V1.42)

password 1234

1[output]

superpassword 19750407

debug

upgradeaddr [empty]

sntpip 0.0.0.0

daylight 0[disable]

timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]

Input ordinary password with debug set as 0[disable], following information will be seen:

AG-168V V1.39 settings

Password:****

P:\>get

iptype 0[static]

ip 192.168.1.100

dns 202.106.196.152

nattraversal 1[enable] nataddr

subnetmask 255.255.255.0

router 192.168.1.254

dns2 202.106.196.115

rtpport 5144

registerport 5142

account [empty]

signalport 5142

pin [empty]

controlport 5144

GATEWAYnumber 182378009 fwdpoweroff 0[disable]

fwdalways 0[disable]

ringtype 0[dtmf0]

password 1234

fwdbusy 0[disable]

answer 5

fwdnoanswer 0[disable]

upgradeaddr [empty]

sntpip 0.0.0.0

daylight 0[disable]

timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]

Command set

Syntax description: set keywords value

Usage: Used to configure password and other running parameters of AG-168V

IP GATEWAY

Detailed description:

set iptype X

Set how IP GATEWAY gets relevant network parameters. X ranged from 0

through 3: 0: authorize users set IP address, subnet mask and router IP

AG-168V SIP GATEWAY User Manual (V1.42)

address of IP GATEWAY manually; 1: use DHCP mode. With this system,

your LAN or router automatically assigns all the required network parameters

to any device connected to it when the device log on. AG-168V IP

GATEWAY is shipped from the factory with DHCP on. So, if your LAN or

router is configured to use DHCP addressing, the IP GATEWAY’s LAN

parameters will automatically be configured as soon as it is connected to the

LAN or router and powered up; 2: use PPPoE mode. Those ADSL and Cable

Modem users please select this item for it is a protocol especially designed

for them. With this system, ADSL ISP automatically assigns all the required

IP parameters to any device connected to it when the device log on; 3: use

modem mode. Those who use IP GATEWAY with modem, please set the

value as 3.

set pppid XXX

With iptype set as 2, use this command to set ADSL ID; with iptype set as 3,

use this command to set Modem ID.

set ppppin XXX

With iptype set as 2, use this command to set ADSL pin; with iptype set as 3,

use this command to set Modem pin.

set ip XXX.XXX.XXX.XXX

With iptype set as 0, use this command to set IP address of AG-168V IP

GATEWAY.

set subnetmask XXX.XXX.XXX.XXX

AG-168V SIP GATEWAY User Manual (V1.42)

With iptype set as 0, use this command to set subnet mask of AG-168V IP

GATEWAY.

set router XXX.XXX.XXX.XXX

With iptype set as 0, use this command to set router IP of network with

AG-168V IP GATEWAY.

set dns XXX.XXX.XXX.XXX

With iptype set as 0, use this command to set IP address of DNS server.

set dns2 XXX.XXX.XXX.XXX

With iptype set as 0, use this command to set IP of backup DNS server.

set mac XX-XX-XX-XX-XX-XX

Set MAC address of the

AG-168V IP GATEWAY. Parameter

xx-xx-xx-xx-xx-xx must be an HEX number.

set service X

Set register the gatekeeper or not. X ranged from 0 through 1. 0: do not

set service type X

Enable/disable the repaid and service system .choose the repaid server

provider. Parameter x ranged from 0 through 29:

0: common: disable repaid card; 4: use Mediaring service; 2: use eTalk card;

3: use Auvtech system; 5: use Ringtec service; 6: use Smartcon service; 7:

use dda service; 8: use vida service; 9: use citron system; 10: use asiasoft

system; 12: use zte system; 13: use huawei system; 16: use asiainfo system;

AG-168V SIP GATEWAY User Manual (V1.42)

17: use Lucent system; 19: use IPN system; 20: use yayuang system; 21:

use thinker system; 22: use suntek system; 28: use txtc system.

set serviceaddr XXXX

Set IP address or domain name of gatekeeper

set serviceid XXXXX

Set service ID according to required by service system

set nattraversal X

Set NAT traversal or not. X ranged from 0 through 7: 0: do not use. When the

supports the IP GATEWAY working behind the LAN; 1: Use NAT traversal.

When the login system does not support IP GATEWAY working behind the

LAN, please use this value to search public IP address of the NAT device.

With this item selected, please make port mapping on NAT device; 2: With

Citron private protocol used, use this value to fit into the GnuGK system

transferring the voice and signal by router; 3: use this value with Innopath

private system used; 5: use this value with vida private system used; 6: aivgr

use this value with aivgr private system used; 7: use this value with Eproxy

private system used.

set nataddr XXXXX

Set IP address of NAT device wan port or URI of free assistant service (Such

as www.showmyip.com etc.) in Internet.

NOTE The free service list of Internet www.ip-calculator.com; www.ipchicken.com;

AG-168V SIP GATEWAY User Manual (V1.42)

www.ipchicken.com;www.showmyip.com;www.whatismyip.com;

www.myipaddress.com; www.whatismyipaddress.com; ip.sbbs.net;

www.whatismyipaddress.net;checkip.dyndns.org

set natttl XX

Set NAT TTL XX is an integer between 10 and 65535 sec. default value is 20

sec.

set GATEWAYnumber XXXXXXXX

Set a GATEWAY number of AG-168V IP GATEWAY . Value xxxxx must be

an Arabic numeral and no longer than 16 characters.

set account XXXXXX

While calling card is set, set account of chosen card; while local type is set

use authentication type, set user ID; while set localtype is set as 1, set SIP

ID.

set pin XXXXXXXXXX

While calling card is set, set password of chosen card; while local type is set

authentication type, set password

set registerport XXXX

Set register port. XXXX is range from 1024 through 6553

set signalport XXXX

This port is Q.931 port using TCP protocol. XXXX is range from 1024 through

65535.

set controlport XXXX

This port is H.245 port using TCP protocol. XXXX is range from 1024 through

65535.

AG-168V SIP GATEWAY User Manual (V1.42)

set registerttl X

Set register TTL. X is range from 10 through 65535 Sec. default value is 60

Sec.

set rtptos X

Set TOS segment of IP head package in RTP digital follow.

set rtpport XXXX

RTP port is the port transferring and receiving voice flow using UDP protocol.

XXXX is range from 1024 through 65535

set jittersize X

Set buffer size of RTP package. X is range from 0-32

set calltype X

Set call type of the GATEWAY. X is ranged from 0 through 2: 0: call out in

normal way; 1: call out in faststart and tunneling way. It is a recommended

way

set localtype X

This command used to set how IP GATEWAY log in gatekeeper. X is

ranged from 0 through 6: 0: use GATEWAY number as E.164 and SIP ID to

set account XXX command; 2:use support automated negotiate about MD5

or CAT authentication system.3:use MD5 authentication account and pin;4:

use CAT authentication account and pin; 5: use SHA1 authentication

account and pin.

set dtmf X

AG-168V SIP GATEWAY User Manual (V1.42)

Set DTMF relay type. X is ranged form 0 through 3: 0:control stringꢀ1:inband

audioꢀ2: signal keypadꢀ3:rfc 2833.

set dtmf payload X

When dtmf X select 3(rfc 2833).This parameter can be used indicating type

of RTP payload type. The value can be use integer 96-101.

set dialplan X

Enable/disable dial plan and dial number. Parameter X ranged from 0

through 4: 0: disable dial plan; 1: enable dial plan; 2: use dial number; 3: use

179XX service.;4: use hotline function.

set dialnumber XX

When set dialplan value set as 2, please use this command to set dial

number. For example, with eTalk card used, please set it as 00. When set

dialplan value set as 4, please use this command to set hotline number.

set dddcode XX

Set the area code when set dialplan value set as 1 or 2. For example, the

area code of Beijing is 10; the area code of Shanghai is 21, and the area

code of Chengdu is 28, etc. Parameter xxx must be an Arabic numeral and

no longer than 3 characters.

set iddcode XXX

Set the country code when set dialplan value set as 1 or 2. For example, the

country code of China is 86; the country code of USA is 1, etc. Parameter

xxxx must be an Arabic numeral and no longer than 4 characters.

AG-168V SIP GATEWAY User Manual (V1.42)

set iddprefix XX

Set IDD service prefix number when set dialplan value set as 1 or 2. For

example, IDD service prefix number of china is 00; IDD service prefix number

of USA is 1, etc. Parameter xxx must be an Arabic numeral and no longer

than 3 characters.

set dddprefix XX

Set DDD service prefix number when set dialplan value set as 1 or 2. For

example, DDD service prefix number of china is 0; DDD service prefix

number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no

longer than 3 characters.

set innerline X

Set use innerline call or not. X ranged from 0 through 1: 0: disable; 1: enable

innerline call.

set localpreifx X

With innerline set as 1[enable] , please set the number switching to local

call, such as 9.

set nonlocalprefix X

With innerline set as 1[enable] , please set the number switching to

long-distance call, such as 9.

set answer X

Set the ring seconds before the GATEWAY answers the call auto or forward

the calls. X is ranged from 0 through 60.

set ringtype X

AG-168V SIP GATEWAY User Manual (V1.42)

Set types of ring. X is ranged from 0 tohrough 12: 0-9: ring as ordinary rings

in different frequency; 10: do not ring; 11: ring as music shipped from factory;

12: ring as music saved by user

set digitmap X

Set whether to use digitmap. X ranged from 0 to 1: 0: do not use digitmap; 1:

use digitmap.

set fwdnumber XXXXXXX

Set receiving forwarded calls GATEWAY number. XXXX must be an Arabic

numeral and no longer than 16 characters

set fwdpoweroff X

Enable/disable forward calls if power off. X is ranged from 0 through 1. 0: do

not forward calls if power off; 1: forward call if power off.

set fwdalways X

Enable/disable forward all calls. X is ranged from 0 through 1. 0: do not

forward all calls; 1: forward all calls.

set fwdbusy X

Enable/disable forward calls if busy. X is ranged from 0 through 1. 0: do not

forward calls if busy; 1: forward call if busy.

set fwdnoanswer X

Enable/disable forward calls without replying. X is ranged from 0 through 1. 0:

do not forward calls without replying; 1: forward call without replying.

set audioframes X

AG-168V SIP GATEWAY User Manual (V1.42)

Set audio frames in RTP package. X is Arabic numerals between 0 and 7.

set 6.3k X

With G.7231, set AG-168V IP GATEWAY to use 6.3K rate or not. X is

ranged from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate.

set vad X

Enable/disable VAD. X is ranged from 0 through 1: 0: disable VAD; 1: enable

VAD.

set agc X

Enable/disable AGC. X is ranged from 0 through 1: 0: disable AGC; 1: enable

AGC.

set aec X

Enable/disable AEC. X is ranged from 0 through 1: 0: disable AEC; 1: disable

AEC.

set handsetin X

Set initial volume of handset. X is ranged from 0 through 15.

set speakerin X

Set initial volume of microGATEWAY of the base. X is ranged from 0 through

15.

set handsetout X

Set initial volume of handout. X is ranged from 0 through 31.

set codec1 X

Set the priority 1of the audio compression algorithm. X is range from 0

AG-168V SIP GATEWAY User Manual (V1.42)

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec2 X

Set the priority 2 of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec3 X

Set the priority 3 of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec4 X

Set the priority 4of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec5 X

Set the priority 5 of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set password XXXX

Set password of the AG-168V IP GATEWAY. XXX must be ASCII

characters.

set superpassword XXXX

Set super password of the AG-168V IP GATEWAY. XXX must be ASCII

characters.

set debug X

Set open debugging message output grade for special tool. X is ranged from

0 through 5: 0: close debugging output; 1: output the operation information to

the window; 2: output all the bug information and data in test window; 3: save

the bug information into SDRAM; 4: disable checks the mark.

AG-168V SIP GATEWAY User Manual (V1.42)

set upgradeaddr XXX.XXX.XXX.XXX

Set IP address or domain name of FTP server supplying upgraded program

of AG-168V IP GATEWAY.

set ntsip XXX.XXX.XXX.XXX

Set IP address of time server.

set daylight X

Set use daylight or not. X ranged from 0 through 1: 0: do not use daylight; 1:

use daylight.

set timezone XX

Set time zone.

Command store

Syntax description: no keyword. Parameter ranged from 0 through 4.

Usage: Save the current settings to the designated position.

Relevant Usage: store 1

Command load

Syntax description: no keyword. Parameter ranged from 0 through 4.

Usage: Load the designated settings to the current position.

Relevant Usage: load 1

Command exit

Syntax description: no keyword and parameter

Usage: Exit from Telnet command window without saving the configuration

Relevant usage: None

Command write

AG-168V SIP GATEWAY User Manual (V1.42)

Syntax description: No keyword and parameter

Usage: Save the configuration and restart the AG-168V IP GATEWAY.

Command ping

Syntax description: ping IP address

Usage: ping IP address of other NAT device

Relevant usage: In telnet window, input ping xx.xxx.xx.xxꢀan IP addressꢀ and

return, then the result will be displayed. If the address is effective, ping OK” will

be seen; if the address is ineffective, nothing will be seen. Fox example

P:\>ping 203.93.9.57

P:\>

ping OK

P:\>ping 27.56.120.56

P:\>

Note Usually, the echo time of ping command is no more than 1 second. So if the

result is not displayed in 5 seconds, ping command is fail.

ftp command

Syntax description: ftp value

Usage: the system connects to the FTP server auto to get the corresponding file

and deal with it

Relevant usage: ftp X

X ranged from 0 through 2:

X-0: Connect to FTP Server to get the file of updating program and save it to the

SDRAM of the GATEWAY. Then the file can be read by PalmTool. This operation

aims at testing.

X-1: Connect to FTP Server to get the file of updating program and update program

Flash. This operation aims at updating program.

X-2: Connect to FTP Server to get the file of updating dial rules and update

program Flash. This operation aims at updating dial rule

Note When you use ftp 0 and ftp 1 commands, if the file get from FTP server is too large

or the net speed is too slow, then the process will not be seen in telnet window.

Please be patient. Using ftp command in telnet to get file spends almost same

minutes as getting file using GATEWAY. So if nothing is displayed after too long

time, it means that ftp is fail.

AG-168V SIP GATEWAY User Manual (V1.42)

Note All the Telnet commands of AG-168V IP GATEWAY should be written in low case

and the password is case sensitive.

ꢀ The usage of AG-168V FXS

ꢀ Receving calls

No matter what calls from IP or PSTN , the phone connecting to AG-168V FXS port

will ring . Mention you that there is call. You can pick up the handset or the speaker

of the normal phone.

ꢀ Call when Dual mode disabled

Call with phone number:

1ꢀ Dial with handset: pickup the handset, dial after dial tone

2ꢀ Dial with speaker: press speaker, dial after dial tone

3. Redial: press redial and call the last number

Call with ip address:

If not registered in gatekeeper and gateway disabled, dial with the ip address:

1. pickup the handset, call after dial tone, press # after numbers

2. Press speaker, input ip address after dial tone, press # after numbers

Notice: Dial with ip address, using * for — .

Call with GATEWAY

If registered in Gatekeeper dial the number.

Pick up the handset or Press speaker, dial the number after the dial tone

AG-168V SIP GATEWAY User Manual (V1.42)

and then press

ꢀ Call when PSTN first Dual mode enabled

ꢁ

Call PSTN number

When PSTN first setted, the way of dial is the same as normal PSTN phone.

Call voip number

ꢁ

ꢀ

Press the cradle or the flash key of the normal phone, enable AG-168 to be in voip

state from pstn first mode. Dial after the dial tone. Refer to “Call when Dual mode

disabled” chaptor

ꢀ Call when IP first Dual mode enabled

ꢁ

Dial voip phone

When ip first was setted , pick up the phone and dial as “Call when Dual mode

disabled”chaptor

ꢁ

Call PSTN phone

Predial the prefix number in the “dual mode prefix”, AG-168V will change to

PSTN line, call after the dial tone.

ꢀ Emergency Call

When AG-168V is power off or in falure, the Normal phone would connect with the

PSTN LINE, work as the “LIFELINE” and call emergency number.

AG-168V SIP GATEWAY User Manual (V1.42)

ꢀ Upgrade AG-168V IP GATEWAY

ꢀ Telnet command to updating

Using telnet , connecting AG-168V FXS, input SuperPassword when registered.

Input ftp X command to update, the value range is 0-2 . detailed meaning is :

x-0 connecting to FTP server, getting the file to updating , and save in the sdram of

the phone. Read from palmtool in order to debug.

x-1 connecting to FTP server, getting the file to updating and refresh the firmware

x-2 connecting to FTP server , getting the file for the dial rule and refresh.

ꢀ Using HTTP

Using HTTP, connecting AG-168V FXS gateway , input SuperPassword when

registered.

Press

, promt the page. Detailed operation refer to

“updating and dial rule chaptor” of “configuration through webpage”

updating through Palmtool

Download the palmtool from www.atcom.com.cn, run the tool and set the ip address on

“IP ADDRESS ” , press the button of “phone settings” , change the “debug” to be “no

check” and save. After rebooting , press the button of “updating ” to get the newest

firmware to updating.

ꢀ Prepare Updated program through FTP

You can ask the server provider for the latest version of program.

ꢀ Operation

1. The service provider must have an FTP server. This server should allow anonymous

AG-168V SIP GATEWAY User Manual (V1.42)

logins.

2. The service provider needs to upload these files to the FTP server:

HardwareTag_ServiceType_Protocol_XXX.bin

This file contains the phone’s firmware binary

HardwareTag_ServiceType_Protocol_cfgXXX.dat

This file contains the phone’s configuration settings

HardwareTag_ServiceType_Protocol_mapXXX.txt

This file contains the phone’s digit map configuration

In the files above HardwareTag is phone’s hardware type, and is identical to the

string in the second line of the LCD display. ServiceType corresponds with the

“servicetype” field in the phone’s settings page. Protocol is the communications

protocol which the IP phone uses. XXX is the version number of the files.

For example if you support the PA168S phone, the “servicetype” is “citron”, the

firmware version is 1.35 and the phone settings and digit map version are both 1.32

then the files on your FTP server should be named as:

PA168S_citron_h323_135.bin

PA168S_citron_h323_cfg132.dat

PA168S_citron_h323_map132.txt

Important: The version number in the file name don’t include the sub version

number. For example, if the version is 1.40.007, then in file name, you should

write 140 only.

If the service provider doesn’t need to upgrade the digit map, it can be omitted from the

FTP server. This will not affect the ability to upgrade phones over the network.

3. All the terminals in the system will do the upgrade if you use the upgrade method in

item 2. But in fact, some customers want to upgrade a special terminal only. So this

way could not fit for this request. We do some modification based on the way in item 2

to provide more way to do the FTP upgrade.

In phone settings, there is a parameter “upgrade type”, the possible value for this

AG-168V SIP GATEWAY User Manual (V1.42)

parameter is "disable", "all", "mac", "pppid", "account", "phonenumber". When select

as "disable" the terminal will NOT do the auto upgrade when select as "all" then the

terminal will do the upgrade as item 2 when select as other value it will add more

check based on item 2’s rule. The detail rules are:

Mac

PA168S_citron_h323_00-09-45-00-00-00_135.bin

PA168S_citron_h323_pppid_135.bin

Ppp id

Account

PA168S_citron_h323_account_135.bin

Phonenumb PA168S_citron_h323_phonenumber_135.bin

The red character is the content for the terminal to check. The configuration

settings and digit map file have same rules. By this way, we could upgrade a special

terminal by FTP.

When upgrade the configuration file, if you select upgradetype as “all”, then the

terminal will keep the network settings, account, pin, servicetype without changing;

but if you select other upgradetype, then the terminal will only keep network settings

and the parameter related with upgradetype without changing. Other settings will all be

rewrite as the configuration file. For example, if you select upgradetype as “account”,

then the terminal will keep network settings and account without changing. All other

settings, like phone number, pin, service type, will changed as the configuration file.

4. Customers must begin with firmware version 1.34 or later. First set the “upgrade

addr” field as the FTP service address(domain name or ip address are all OK) , and

ensure that the “servicetype” is same as the service provider requested. After the phone

is rebooted, it will connect to the FTP server automatically. It will then check the

filenames for type and version. If it finds the matching file with a later version than

that which is installed then it will perform an upgrade. If all three files have a new

version, the phone will upgrade in the following order: phone setting first, then digit

map after rebooting, and then firmware binary after rebooting again. If the server

version is not newer than current version in the phone, no upgrade is performed. This

guarantees that customers have the latest firmware installed at all times..

Since it may take about ten minutes to upgrade some kinds of firmware binaries, we need

customers to verify that they want to upgrade at this time. The phone will display “Sure to

Upgrade” on the LCD to prompt customers before it does the upgrade.The customers can use the

“Handfree” key to confirm it.

For the service provider, this system gives the flexibility to decide whether the latest

version contains changes worth supporting. For example if the current firmware is 1.34

AG-168V SIP GATEWAY User Manual (V1.42)

and there are no new features of use to them in our 1.35 and 1.36 versions, then they

don’t need to put these files on FTP server. The customers will continue to use version

1.34. However if we have some useful features in 1.37, then by uploading the new files

to the FTP server all customers will be upgraded at their next system reboot.

4. We also support manual FTP upgrades via the keypad on phones. If the service

provider decides to use this feature, the following files also need to be uploaded:

HardwareTag.bin

HardwareTag.dat

HardwareTag.txt

firmware binary

phone settings

digit map

Here HardwareTag is phone’s hardware type, as in item 2 above.

A manual firmware upgrade is performed by picking up the phone and pressing

Phone Password (default: 1234) + n + LocalIP_Key

If n = 5, the phone settings are upgraded

If n = 6, the digit map is upgraded

If n = 8, the firmware is upgraded

Reserves the right to make changes in technical and product

specification without prior notice.

AG-168V SIP GATEWAY User Manual (V1.42)

EFJohnson Portable Radio 002 8170 001 User Manual
EverFocus Car Video System EN 7517C User Manual
Everpure Plumbing Product Contemporary Series User Manual
Everpure Water System CG53 10 User Manual
Extron electronic Home Theater System MP 101 User Manual
Fluke Carbon Monoxide Alarm CO 220 User Manual
Fluke Slow Cooker Ti30 User Manual
Frymaster Toaster HLZ User Manual
GarrettCom Switch 84 00136 User Manual
Gemini Musical Instrument KL 10 PRO User Manual