Cutout Template
224 mm x 326 mm
(8.8” x 12.85”)
Paint Guard
SI 28W
In-Wall Speaker
User’s Guide
1
4
Determine speaker location.
Insert the speaker into the wall opening.
Leave at least 1” clearance from the edge of the speaker
to the studs in all directions. Hold or tape template in location,
make sure template is level. Trace along the inside of the template.
Loosen the six screws on the front baffle (counter
clockwise) 1/2 turn. Then tighten the screws (clockwise)
until the dog legs clamp the speaker to the wall.
At least 1” from the stud.
Trace template.
2
5
Carefully cut a hole along the inside of the traced line.
Level speaker, position each wall clamp outward, and tighten
each screw until snug.
Install dust shield to protect the speaker during ongoing
construction.
Cut material.
CAUTION
Do not over-tighten screws.
3
Attach the speaker wires to the 2-pole captive screw plug.
Use red for the positive (+) wire and black for the negative (-)
wire. Insert the 2-pole captive screw plug into the 2-pole
connector on the back of the speaker.
Dust Shield
6
Remove the dust shield,
install the speaker grill.
r
ke
SIll28W
Spea
a
In-W
ce
s
n
da
e
p
8
m
Oh
Im
0
XX 00/0
red
Enginee
XXXX
SN XXXX
E
XXX
i
n
U
S
A
-01
235
-1
33
Application diagram:
Specifications:
Acoustic & Electrical
Speaker type.................................. 2-way in-wall speaker
Frequency range........................... 30 Hz to 20 kHz, -10 dB, half space
Power capacity.............................. 70 W continuous program,
35 W continuous pink noise
T
TPU
OU
FT
IED
LE
PLIF
M
A
T
GH
RI
V
12
IR
Rx
B
Tx
A
R
/I
C
M
C
L
S-232/ MP
R
EA
PR
S
T
PU
T
2
I
O
I
N
EOU
IN
L
D
1
U
L
A
SI 28W
Projector
L
IX
X/M
U
ST
JU
A
D
A
-42dB
O
T
+24dB
IO
IO
D
U
A
S
R
T
EVEL
L
O
PU
IN
E
M
IN
L
ON
D
U
A
5
6
Two-way In-wall
Speaker
R
Nominal sensitivity......................
Nominal impedance .................... 8 ohms
Crossover frequency................... 2.5 kHz
Woofer........................................... 8" (203 mm) polypropylene cone with
moisture resistant coating
89 dB SPL, 1 W, 1 m, half space
B
S
G
T
PU
T
OU
R
I
M
R
S
T
EO
VID
PU
IN
Extron
MLS 304SA
MediaLink Switcher
50-60Hz
2
240V
100-
1
MAX.
0A
1.
Tweeter.......................................... 1" (25 mm) titanium dome
General
Temperature/humidity...............
Laptop
w/ Audio
Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Warranty ....................................... 5 years parts and labor
PC
VCR
NOTE: All nominal levels are at 10%.
NOTE: Specifications are subject to change without notice.
68-1102-01 Rev. A
08 07
Print at 100% - Do Not “Fit to Paper”.
|